美国德纳科Dynalco PG-100 Pulser脉冲发生器

Download Info:
PG-100 Data Sheet & Manual Product Code: PG-100

转速表：转速脉冲器

5/8x18螺纹“1”螺纹

3/4x20螺纹的“2”螺纹
TACHOMETER: RPM pulser
"-1" tapped for 5/8x18 thread
"-2" tapped for 3/4x20 thread
PG-100每转产生60个脉冲，由一个完整的磁性拾波器（不包括在内）。它直接安装在直径为0.50至1.25英寸（1.27至3.18厘米）的轴上，使用可拆卸锥形锁衬套。信号直接输入仪表、速度开关等。无需外部电源。当外部齿轮不可用时有用。
The PG-100 generates 60 pulses per revolution from an integral magnetic pickup (not included). It mounts directly on 0.50 to 1.25 inch (1.27 to 3.18 cm) diameter shafts using a removable taper lock bushing. The signal feeds directly into meters, speed switches, etc. No external power is required. Useful when an external gear is not available.

Dynalco PG-100 RPM Pulser
Converts Shaft Rotation into Signal Frequency

Dynalco PG-100转/分脉冲发生器提供

输出频率成正比

以赫兹为单位的数值等于

安装在其上的轴。不

需要外部电源。轴径

从1/2英寸到1-1/4英寸，增量

可容纳1/16英寸。这个

PG-100开发了一个使用的信号频率

使用Dynalco的电子转速表，

其他累加器，频率至直流电

转换器和类似设备。The PG-100 RPM Pulser provides an
output frequency directly proportional and
numerically equal, in Hz, to the RPM of
the shaft on which it is mounted. No
external power required. Shaft diameters
from 1/2 inch to 1-1/4 inches, in increments
of 1/16 inch, can be accommodated. The
PG-100 develops a signal frequency used
with Dynalco’s electronic tachometers,
other totalizers, frequency-to-DC
converters, and similar equipment.

FEATURES
The PG-100 can be used when a gear is not
available on the shaft to generate a signal frequency
from a magnetic pickup, or when it is more convenient
to slip on theis transducer than to mount a gear or
sprocket with associated bracket to hold the
magnetic pickup with appropriate spacing.
Thre are 60 gear teeth on the rotor inside the PG-
100. The gear teeth face the pole piece of the
magnetic pickup mounted on the fixed-position
outer ring. The pickup guard is positioned against a
fixed surface to prevent movement of the outer ring.
As the shaft rotates, a signal frequency, numerically
equal to rpm, is generated by the pickup. The
waveshape of the output voltage is approximately
sunusoidal.
The PG-100 RPM Pulser provides an
output frequency directly proportional and
numerically equal, in Hz, to the RPM of
the shaft on which it is mounted. No
external power required. Shaft diameters
from 1/2 inch to 1-1/4 inches, in increments
of 1/16 inch, can be accommodated. The
PG-100 develops a signal frequency used
with Dynalco’s electronic tachometers,
other totalizers, frequency-to-DC
converters, and similar equipment.
For every shaft revolution, 60 pulses or cycles are
produced; a shaft rotating at 1 rpm produces 60
cycles in one minute or 1 cycle per second so:
Rpm (of shaft) = Frequency in Hz
(of pickup output voltage).
The PG-100 can be equipped with magnetic pickup
M101 (standard), M102 (for low speed applications),
or any other Dynalco pickup with a pole piece of
0.106 inch diameter or less. Refer to the Dynalco
pickup catalog for full specifications and
characteristics of these pickups.
At a load resistance of 5,000 ohms or greater, 0.005
inch gap, typical ouputs are:
M101: 2 mVrms per rpm
M102: 6 mVrms per rpm
The PG-100 Rpm Pulser is designed for use over
shaft speed ranges up to 0 - 2000 rpm. It employs a
permanently lubricated, shielded, and sealed
bearing. No brushes, slip rings, or other parts that
wear out over time are used

- PG-100-1: tapped for 5/8-18 pickup
- PG-100-2: tapped for 3/4-20 pickup
- Converts shaft rotation into signal
frequency output via internal 60 tooth
gear.
- Maximum shaft speed: up to 2,000 RPM
- Permanently lubricated, shielded,
sealed bearing. No brushes or slip
rings.
- Output waveform is approximately
sinusoidal.
- For every shaft revolution, 60 pulses or
cycles are produced.
A shaft rotating at 1 RPM produces 60
cycles in one minute or 1 cycle per
second, so: RPM (of shaft) = Frequency
in Hz (of pickup output voltage).
- For shaft diameters from 1/2 inch to 11/4
inches (in increments of 1/16 inch).
Specified when ordering.
- Pickup guard to be positioned against a
fixed surface to prevent movement of the
outer ring.
Pickup Specs: Acceptable Pickups
- M101 (standard).
- M102 (low speed applications).
- Any other Dynalco pickup with a pole
piece diameter of 0.106 inch diameter or
less.
- At a load resistance of 5,000 ohms or
greater, 0.005 inch pole piece gap,
typical outputs are:
- M101: 2 mVrms per RPM
- M102: 6 mVrms per RPM
BUSHING DIMENSIONS
BORE DIAMETER KEYWAY SIZE
1/2 in. to 9/16 in. 1/8 in. X 1/16 in.
5/8 in. to 7/8 in. 3/16 in. X 3/32 in.
15/16 in. to 1-1/4 in. 1/4 X 1/8 in.
PG-100 RPM Pulser
WEIGHT
Less than 4 lbs (1.8 kgs)—including
optional pickup and cable assembly.

美国德纳科Dynalco控制仪表公司简介

美国德纳科Dynalco公司设计和制造高度工程坚固，可靠的，第三方的监测，控制和往复式发动机，蒸汽涡轮机，燃气涡轮机，泵和输送系统的保护认证仪表。我们为一个在石油和天然气，化工/过程，建筑业及越野设备，交通运输，发电，船舶，采矿，水和废水市场的客户和工厂自动化等。Dynalco designs and manufactures highly engineered rugged, reliable, 3rd party certified instumentation for monitoring, control and protection of reciprocating engines, steam turbines, gas turbines, pumps and conveying systems. We serve a variety of customers in the Oil and Gas, Chemical/Process, Contruction and off-road equipment, Transportation, Power Generation, Marine, Mining, Water and Waste Water and Factory Automation Markets. 

Dynalco 1968年创立，有三种产品，以及为石油和天然气工业生产工程解决方案的目标。自那以后的47年里，Dynalco已经成为世界范围内的工业领袖，因其在石油和天然气、化学、电力、海洋和建筑行业使用的高质量的仪器和控制而得到认可。Dynalco was started in 1968, with three products and a goal of producing engineered solutions for the oil and gas industries. In the 47 years since, Dynalco has become a worldwide industry leader, recognized for its high-quality instruments and controls used in the oil & gas, chemical, power, marine and construction industries.

 

- Dynalco Products

MTH-103E Tachometer / Hourmeter / Overspeed Trip 
UM-200 Tachometer / Hourmeter / Monitor 
Catalyst Monitor 
UM-600 Universal MonitorInstruments & Controls for Rotating Equipment in 
Demanding Applications 
Recently Updated Products M928-24 Magnetic Pickup/Speed Sensor 
MTH-103D Tachometer / Hourmeter / Overspeed Trip 
SST-2400H Speed Switch/Transmitter 
SWTD-1000 Speed Switch/Transmitter
LMD-120A Panel Meter 
LMD-120D Panel Meter
DPM-105 Panel Meter 
UM-600 Universal Monitor

Engine Controls & Emissions Controls 
Instruments/Gauges/Meters 
- General Purpose Gauges/Meters 
- Hourmeters 
- Tachometers 
- Temperature Gauges/Meters 
- Universal Scanner Magnetic Pickups/Speed Sensors 
- Active (Powered) 
- Cable Assemblies 
- Extra Long Reach 
- Hazardous Area 
- Intrinsically Safe Barriers 
- Miniature 
- Power Source 
- Standard Power Generation 
Dynalco Speed Switches & Speed Transmitters 
- DIN Rail and DIN Standard Series 
- SST Series

- Dynalco Tachometer转速表

Dynalco Tachometers转速表型号

CRT-9x - Replacement Tachometers;The CRT-9X replaces Caterpillar tachometers: CAT-9X114, CAT-9X116, and CAT-9X117. SPD-100 ; SPD-100L ; SPD-108 ; SPD-108L; MTH-103D; F-16; DS-800; DS-900; SPD-700; SPD-708; LST-100; LST-100L; LST-108; LST-100; LST-108L; DST-2000C; PG-100; TT-1; TT-100；DPM-105，LMD-120A，LMD-120，LMD-120D，G-101。

Dynalco Speed Switch 速度开关型号

SST-2000A；SST-2000H ；SST-2000A/H；SST-2200A；SST-2400A；SST-2200H；SST-2400H；SW-200B；SW-50；PNT-202

DYNALCO SST-2000 Series Speed Switches/ Transmitters Product
SST-2000A Speed Transmitter
SST-2000H Speed Transmitter
SST-2200A Speed Switch/Transmitter
SST-2200H Speed Switch/Transmitter
SST-2400A Speed Switch/Transmitter
SST-2400H Speed Switch/Transmitter

Dynalco Pickup Sensor传感器型号

M104; M202; M208，M101 ，M102 ，M131，M133 ，M142 ，M151 ，M155 ，M168 ，M183 ，M184，M189 ，M343 ，M801 ，M802 ，M928 ，M137 ，M138 ，M143 ，M104，M134 ，M135 ，M139， M140，M180 Magnetic Pickup/Speed Sensor ，M201 ，M202 ，M203 ，M204 Magnetic Pickup Speed Sensor，M205 ，M219 ，M231 ，M233，M318 ，M319 Magnetic Pickup/Speed Sensor，M107 ，M207 ，M208 ，C101-10 ，C910-10 ，C917-10 ，HTM-801； M806 Hall Effect Magnetic Pickup/Speed Sensor ; M951 Hall Effect Magnetic Pickup/Speed Sensor 。 Dynalco temperature indicator温度指示仪型号:TMP-100 ; STM-110-11；STM-110-13 ; STM-110-14 ; TID-110; TMP-900。